Ditulis Oleh : YK69 Elektro
Judul : Hifi stereo pre-amp head
Hifi stereo pre-amp head
This is hifi stereo pre-amp head with tone control circuit Using a special IC TDA1524A
All signal processing is done within the TDA1524A by voltage controlled amplifiers and voltage controlled filters. The IC provides a fixed voltage (~ 3.8V DC) at pin 17, and this is used by all the variable resistors to provide an adjustable DC voltage to the appropriate control pins.
Current sensing is used to provide a flat response when R5 is connected to pin 17, and a loudness contour when disconnected. 100 nF capacitors are used on each pot to decouple any AC signals from the control inputs. 10 uF capacitors are used to couple both input and output audio signals whilst blocking DC. R1 and R2, are to ensure stability with capacitive loads. R3 and R4 make sure there are no DC spikes at the output sockets if the load is switched. C3 and C4 control the loudness contour. C5 and C6 control the treble turn-over frequency. C18 and C19 have been added to roll off the gain above 70 kHz. Low volume settings coupled with treble boost was causing HF instability in some instances. This should no longer be a problem.
All signal processing is done within the TDA1524A by voltage controlled amplifiers and voltage controlled filters. The IC provides a fixed voltage (~ 3.8V DC) at pin 17, and this is used by all the variable resistors to provide an adjustable DC voltage to the appropriate control pins.
Current sensing is used to provide a flat response when R5 is connected to pin 17, and a loudness contour when disconnected. 100 nF capacitors are used on each pot to decouple any AC signals from the control inputs. 10 uF capacitors are used to couple both input and output audio signals whilst blocking DC. R1 and R2, are to ensure stability with capacitive loads. R3 and R4 make sure there are no DC spikes at the output sockets if the load is switched. C3 and C4 control the loudness contour. C5 and C6 control the treble turn-over frequency. C18 and C19 have been added to roll off the gain above 70 kHz. Low volume settings coupled with treble boost was causing HF instability in some instances. This should no longer be a problem.
C15, 16, 17 provide power supply filtering. D1 provides protection in case of incorrect supply polarity. The LED is a power on indicator and may be omitted if not required, or preferably mounted on the enclosure. If you are not using a switch pot, you can connect an external switch across the P1 switch pins, or connect a wire link there and switch the power supply.
The power supply is critical to the noise performance of the pre-amp head. An on board regulator is provided to reduce mains hum. If you wish to use it with a car or other 12V battery, then you should omit the 7812 regulator, and place a wire link between the regulator input and output pin positions on the PC board. Do not short to earth! This will be necessary because the regulator must have an input voltage at least 2-3V greater than it’s output, for it to maintain regulation. However the regulator will not be necessary with a battery supply.
If using a plug pack, it’s output voltage should be 15 to 18V DC. Because most plug packs have poor regulation, one rated at 12V DC will often be around 15V when lightly loaded. The current drain of the pre-amp is less than 50 mA, so many 12 V unregulated supplies may be adequate if you have one. Replace D1 with a wire link if necessary, making sure you have the supply polarity correct!
If you are using a 15-20V supply for your power amplifier, you can use that as your pre-amp supply as well. Make sure you test the voltage first in all cases.
The power supply is critical to the noise performance of the pre-amp head. An on board regulator is provided to reduce mains hum. If you wish to use it with a car or other 12V battery, then you should omit the 7812 regulator, and place a wire link between the regulator input and output pin positions on the PC board. Do not short to earth! This will be necessary because the regulator must have an input voltage at least 2-3V greater than it’s output, for it to maintain regulation. However the regulator will not be necessary with a battery supply.
If using a plug pack, it’s output voltage should be 15 to 18V DC. Because most plug packs have poor regulation, one rated at 12V DC will often be around 15V when lightly loaded. The current drain of the pre-amp is less than 50 mA, so many 12 V unregulated supplies may be adequate if you have one. Replace D1 with a wire link if necessary, making sure you have the supply polarity correct!
If you are using a 15-20V supply for your power amplifier, you can use that as your pre-amp supply as well. Make sure you test the voltage first in all cases.
Demikianlah Artikel dari kami yang berjudul Hifi stereo pre-amp head,apakah anda menyukainya ? mudah-mudahan artikel ini bisa memberi manfaat untuk anda semua.
Anda sedang membaca artikel Hifi stereo pre-amp head dan artikel ini url permalinknya adalah https://yk69.blogspot.com/2009/10/hifi-stereo-pre-amp-head.html Artikel yang anda cari Lainnya bokep, video bokep, streaming bokep, streaming , videos, porn, videos porn, kimcil, bugil, telanjang, abg, mesum, tetek, memek, toket, masturbasi, bmf, download, perkosa, kepergok, mesum, pemerkosaan, kepergok mesum, download video porn, download video bokep, bokep terbaru, streaming bokep terbaru, jilbab, semok, ngentot, indo, janda, asia, orgasme, meki, sex, video sex, spg, streaming mesum, ml, tante, streaming abg, cabe cabean, cantik, manis, bokep indo, bokep cinta, streaming mesum, hot bokep, bokep hot, abg bugil, anak smp, bocah smp, anak sma, bocah sma, indonesia, 3gp'
- 3VDC Stereo Headphone Amplifier by IC LM4910 - New!
- 9 Volt Portable Headphone Amplifier Circuit
- Audio Peak Level Indicator By Op-Amp
- Op-Amp 6-Line Audio Mixer Circuit
- Rangkaian 11-90 hz Subwoofer Filter Using TL072 Op-Amp
- Rangkaian Alat Bantu Pendengaran
- Rangkaian Audio Surround Decoder
- Power Meter Schematic For Audio Amplifier
- Sound Level (Decibel) Meter Circuit
- Ukuran Box Subwoofer 10" - New!
- 9 Second Countdown Power-On Relay With 7 segment Display
- DC Motor Controller Circuit Using 741 Op-Amp
- Darlington Pair to Drive DC motor Circuit
- Simple Switch On Time Delay Circuit
- Stepper Motor Controller using IC 4027 - New!
- 100Watt Inverter Circuit by IRF44 Mosfet
- 12VDC to 220VAC Inverter Circuit Using IC 555
- 12VDC – 220VAC Inverter Using Cmos CD4047
- 500 Watt Inverter 12VDC to 220VAC
- 25V Capacitor Bank for OCL Amplifier
- 30W Mini Mosfet Amplifier
- 35W Audio Amplifier Circuit by STK082
- 4,8W Class-A MOSFET Amplifier - New!
- BA5417 Stereo Power Amplifier Circuit - New!
- LM383 - Car Audio Amplifier Circuit - New!
- Power Meter Schematic For Audio Amplifier
- Rangkaian 400W MOSFET Amplifier
- Rangkaian Power Amplifier Blazer 1000 Watt - New!
- Sound Level (Decibel) Meter Circuit
- 9 Second Countdown Power-On Relay With 7 segment Display
- Driver Relay Menggunkan Transistor
- Light/Dark Switch With Relay
- Simple Switch On Time Delay Circuit
- Simple switch-Off Time Delay Circuit
- Car Parking Sensor circuit Using Infra-Red LED
- Rangkaian Pendeteksi Angin - New!
- Smoke Detector circuit Using LDR
- High Voltage Meter or Probe Design
- Power Meter Schematic For Audio Amplifier
- Rangkaian Ampere Meter Digital
- Rangkaian Transistor Tester
- Sound Level (Decibel) Meter Circuit
0 Response to "Hifi stereo pre-amp head"
Post a Comment