Ditulis Oleh : YK69 Elektro
Judul : Rangkaian 400W MOSFET Amplifier
Rangkaian 400W MOSFET Amplifier
These amplifiers circuit can be used for virtually any application that requires high performance, low use Noise, distortion and excellent sound quality. Examples would be subwoofer amplifier should FOH stage Amplifiers, surround a canal a very powerful sound amplifier, etc. The 400W MOSFET-amplifier has four key stages of amplification. We are looking to start any Phase appropriate detail.
Skema Rangkaian 400W MOSFET AmplifierNote:
- Use + /-70V 10A DC dual supply for powering the circuit.
- For L1 make 12turns of enameled copper wire on a 1cm him: plastic formers.
- use 8 x IRFP448 MOSFETs in the final stages
- Heat sink is Necessary for the MOSFETs. A 8x4x4 inch finned aluminum heat sink will do. There is no such thing as a heat sink That is too large.
As the name suggests All Q ,C and ZD the Bias and buffer phases. Its main goal is to provide a stable MOSFET Gates and offset voltage and the voltage buffer amplifier stage of the High Resource capacity. What would have without the phase response and the effect Slew rate is indeed very bad. The flip side of the coin is not the extra step Introduction of an additional dominant pole in the amplifier feedback loop.
Also to what the name suggests this stage converts the voltage developed in the VAS and provides all the amps required to drive at 8 or 4 ohms. 2-ohm loads are possible for several minutes at a time. In fact, I have tested more than 1600 1kW amplifier Watts RMS at 2 ohms. But that would not be recommended as a long-term exposure at all. If it is higher than the figures of the STI-amp. Power to the AV amplifier 800 The components of the power for this amplifier are as follows, and are favored A channel or a power module alone. 1 toroidal transformer with a rating of 1kVA. Primary windings are made to fit
Also to what the name suggests this stage converts the voltage developed in the VAS and provides all the amps required to drive at 8 or 4 ohms. 2-ohm loads are possible for several minutes at a time. In fact, I have tested more than 1600 1kW amplifier Watts RMS at 2 ohms. But that would not be recommended as a long-term exposure at all. If it is higher than the figures of the STI-amp. Power to the AV amplifier 800 The components of the power for this amplifier are as follows, and are favored A channel or a power module alone. 1 toroidal transformer with a rating of 1kVA. Primary windings are made to fit
Demikianlah Artikel dari kami yang berjudul Rangkaian 400W MOSFET Amplifier,apakah anda menyukainya ? mudah-mudahan artikel ini bisa memberi manfaat untuk anda semua.
Anda sedang membaca artikel Rangkaian 400W MOSFET Amplifier dan artikel ini url permalinknya adalah http://yk69.blogspot.com/2011/04/rangkaian-400w-mosfet-amplifier.html Artikel yang anda cari Lainnya bokep, video bokep, streaming bokep, streaming , videos, porn, videos porn, kimcil, bugil, telanjang, abg, mesum, tetek, memek, toket, masturbasi, bmf, download, perkosa, kepergok, mesum, pemerkosaan, kepergok mesum, download video porn, download video bokep, bokep terbaru, streaming bokep terbaru, jilbab, semok, ngentot, indo, janda, asia, orgasme, meki, sex, video sex, spg, streaming mesum, ml, tante, streaming abg, cabe cabean, cantik, manis, bokep indo, bokep cinta, streaming mesum, hot bokep, bokep hot, abg bugil, anak smp, bocah smp, anak sma, bocah sma, indonesia, 3gp'
0 Response to "Rangkaian 400W MOSFET Amplifier"
Post a Comment