Rangkaian Osilator Gelombang Sinus Variabel.

Rangkaian Osilator Gelombang Sinus Variabel. - Hallo sahabat YK69 Elektro, Pada kesempatan kali ini saya akan membahas artkel yang berjudul Rangkaian Osilator Gelombang Sinus Variabel., saya telah menyediakan berbagai macam artikel terbaru lainnya. mudah mudahan artikel yang saya tulis ini bermanfaat buat anda semuanya.

Ditulis Oleh : YK69 Elektro
Judul : Rangkaian Osilator Gelombang Sinus Variabel.

lihat juga


Rangkaian Osilator Gelombang Sinus Variabel.

Osilator Gelombang Sinus Variabel (15 to 150kHz)

This is a circuit of sine wave oscillators covering a frequency range of 15 to 150kHz in four switched steps. Two conditions exist for a sinusoidal oscillator. Regenerative or positive feedback, and a closed loop gain of unity. The losses in the wien feedback circuit, are such that the open-loop gain of the amplifier must also exceed 3.

rangkaian osilator sinus variabelSkema rangkaian osilator sinus variabel


The circuit gain is provided by a FET type op-amp (LF351), but LF351 may be difficult to obtain, for a replacement you can use TL071CN or TL081CN. The Maplin order codes are RA67X and RA70M respectively. The wien network is a parallel combination of resistors and capacitors, in series with a series RC network. Regenerative feedback is applied from the op-amp output, to the serail RC input and continues. Stabilization is required to prevent the otherwise Uncontrolled oscillation from building up and becoming unstable.

There are two common methods of stabilizing a wien oscillator type. A thermistor with a NTC in the series leg of the feedback loop or an incandescent lamp (with a positive temperature coefficient) in the shunt leg of the feedback loop. The bulb used here is a 6V 60mA type Maplin code BT99H. A 12 Volt bulb rated 60mA or 40mA will also work. The feedback arrangement works as follows. As a bulb filament heats up its resistance increases. This will decrease the overall gain of the amplifier, as the output signal is fed back to the input.Similarly, if the output of the signal amplitude decreased Appearing at the bulb would be less, its filament resistance would drop and the gain would be increased. Therefore a stable output amplitude is produced. The 1k preset is adjusted for minimum distortion. Note that split supplies are used and a ganged 10k Potentiometer controls with a 10:1 frequency range.


Demikianlah Artikel dari kami yang berjudul Rangkaian Osilator Gelombang Sinus Variabel.,apakah anda menyukainya ? mudah-mudahan artikel ini bisa memberi manfaat untuk anda semua.

Anda sedang membaca artikel Rangkaian Osilator Gelombang Sinus Variabel. dan artikel ini url permalinknya adalah http://yk69.blogspot.com/2010/01/rangkaian-osilator-gelombang-sinus.html Artikel yang anda cari Lainnya bokep, video bokep, streaming bokep, streaming , videos, porn, videos porn, kimcil, bugil, telanjang, abg, mesum, tetek, memek, toket, masturbasi, bmf, download, perkosa, kepergok, mesum, pemerkosaan, kepergok mesum, download video porn, download video bokep, bokep terbaru, streaming bokep terbaru, jilbab, semok, ngentot, indo, janda, asia, orgasme, meki, sex, video sex, spg, streaming mesum, ml, tante, streaming abg, cabe cabean, cantik, manis, bokep indo, bokep cinta, streaming mesum, hot bokep, bokep hot, abg bugil, anak smp, bocah smp, anak sma, bocah sma, indonesia, 3gp'
,Rangkaian Osilator Gelombang Sinus Variabel. xxx .

0 Response to "Rangkaian Osilator Gelombang Sinus Variabel."

Post a Comment